상세 가이드 곧 제공 예정
3D Print Filament Usage에 대한 종합 교육 가이드를 준비 중입니다. 단계별 설명, 공식, 실제 예제 및 전문가 팁을 곧 확인하세요.
The 3D Print Filament Usage Calculator converts model volume (cm³) to grams of filament consumed and meters of filament extruded — essential for predicting whether your current spool has enough filament for a large print and for ordering replacement spools in time. Conversion uses material density (PLA 1.24 g/cm³, PETG 1.27, ABS 1.04, TPU 1.20, nylon 1.13, PC 1.20) and filament diameter (1.75mm or 2.85mm). The geometric relationship: filament is a cylinder, so length × π × (radius)² = volume, allowing conversion from extruded volume to linear meters. Why both grams and meters: spools sell by weight (1 kg standard); machines and slicers track usage in meters. A 1 kg PLA spool contains ~330 meters of 1.75mm filament (1000 g / 1.24 g/cm³ / (π × 0.875² cm²) ≈ 333 m). When slicers report 'used 124 meters' you can convert to grams (~373 g) to know how much spool remains. Conversely, a slicer reporting '180 g' equals ~60 m extruded. For PETG (denser at 1.27), 1 kg ≈ 322 m. For TPU at 1.20, 1 kg ≈ 335 m. For 2.85mm filament, lengths are ~38% shorter at same weight (larger cross-section). Most modern printers use 1.75mm; legacy Ultimaker and some industrial machines use 2.85mm. Mixing diameters causes feeder/hotend issues — match filament diameter to printer specification. Who needs this: print operators planning multi-day prints (need to know if spool will last), spool inventory managers, comparing 'cost per meter' across brands (sometimes more honest than 'cost per kg' since meters depend on density), and slicer setup validation (cross-check that slicer reports match expected values for a known volume). For makers tracking total filament consumed over time, this calculator converts model libraries' published volumes into purchasing forecasts.
- 1Step 1 — Get model volume from slicer estimate or CAD report (cm³)
- 2Step 2 — Select material type — density populates automatically (PLA 1.24, PETG 1.27, etc.)
- 3Step 3 — Select filament diameter (1.75mm standard, 2.85mm for older Ultimaker)
- 4Step 4 — Calculator computes mass: Volume × Density
- 5Step 5 — Computes cross-section area: π × (Diameter / 2)²
- 6Step 6 — Computes length: (Volume × 1000) / Area in mm, then divides by 1000 for meters
- 7Step 7 — Outputs grams, meters, and millimeters for verification
50 × 1.24 = 62g mass. Cross-section: π × 0.875² ≈ 2.405 mm². Length: 50,000 mm³ / 2.405 mm² ≈ 20,790 mm ≈ 21 m. With slight rounding, ~26 m.
300 × 1.27 = 381g; ~158m. About half a kilogram spool (would leave 38% for next print).
TPU prints slower but consumes similar filament per cm³ to PLA
150 × 1.20 = 180g. TPU is similar density to PLA, just slower to print.
Same mass (124g) but 2.85mm filament is ~2.6× thicker in cross-section, so length is ~40% shorter than 1.75mm equivalent.
Multi-day print planning (will the spool last?)
Spool inventory management
Cost-per-meter comparison across brands
Slicer setup validation
Maker class project filament budgeting
Print farm material allocation
Why do different materials have different densities?
Polymer chemistry. PLA's lactic acid backbone packs slightly more densely than ABS's styrene chains. PETG, with its ethylene-glycol modification, is densest of common materials. Carbon fiber composites raise density (1.30+) due to embedded fibers. Foaming PLA reduces density (0.9 typical) for lightweight prints. Density affects mass per cm³ but not length per cm³ at fixed diameter.
How does this differ from slicer estimates?
Slicer estimates account for actual extrusion path including infill pattern, line widths varying for slow zones, support material, brims, and purge towers. This calculator gives the pure geometric conversion of finished model volume to filament. For ordering decisions, multiply this by 1.1–1.2 to include slicer overhead.
Is 1.75mm or 2.85mm filament better?
1.75mm dominates the modern hobby and prosumer market (Bambu, Prusa, Voron, Creality all use 1.75mm). 2.85mm persists in legacy Ultimaker and industrial machines — physically more stable in feeders but requires larger hotends. Match your printer's specification; you cannot interchange.
Do I need to recalibrate when switching materials?
Yes for temperature and bed adhesion, but not for the length/mass conversion — this calculator uses material density which is fixed property. Slicer e-steps (extrusion calibration) compensate for material flow differences at the hotend level.
What about TPU's flexibility — does it affect length conversion?
No — density and diameter govern the conversion. Flexibility affects how the filament feeds (TPU requires direct drive extruder) and how fast it can print, but a 100 cm³ TPU model uses the same grams as 100 cm³ of any other 1.20 g/cm³ material.
전문가 팁
When ordering filament for a known print, multiply this calculator's output by 1.15 for safety margin (covers brim, supports, purge tower, and the inevitable failed first attempt). A 600g spool needs to last for a 500g model — too tight without margin.